Dealing with a Unexpected Hot Water System Failure: Key Steps

Show Details

We've unearthed the article pertaining to How to Troubleshoot and Repair an Electric Water Heater listed below on the web and felt it made sense to talk about it with you over here.


What Would Cause My Electric Water Heater to Stop Working?
Several modern-day residences use an electric hot water heater for their heating unit, due to its convenience and also simplicity of use. Nevertheless, just like any other electric home appliances, troubles might emerge with its use, unexpectedly. It can be truly irritating to awaken to a chilly shower instead of a warm one or having your bath with water that isn't hot sufficient or perhaps as well hot. Whatever the case might be, hot water heater troubles can be fairly stressful. The good news is, we've made a checklist of possible services to your hot water heater issues. There are a number of factors that could trigger a lot of these troubles, it could be a concern with the power supply, the electrical burner, or the thermostat. Prior to doing anything, ensure you switch off the primary power supply for security. Whatever the issue is, getting it repaired should not position too much of a problem if you follow these steps:

Call A Specialist:


If after replacing all defective parts and resetting your temperature, the water heater still isn't functioning, you might need to get in touch with an expert plumber for a professional viewpoint. The issue with your heating unit could be that the cold and hot taps have actually been switched over or it may be undersized for the quantity of hot water needed in your house. Whatever the situation might be, a professional plumber would aid fix the trouble.

Inspect Your Power Supply:


As standard as this might appear, it is really required. Without adequate power, your water heater will not work. So the first thing to do when your water all of a sudden stops working is to verify that it isn't a power trouble. Examine if the fuse is blown out or the breaker tripped. If the circuit breaker is the issue, merely turn it off and on again. Replace any kind of broken or damaged fuse. Test the appliance with power after these modifications to see if it's now functioning.

Examine Your Thermostat:


If your hot water heater still isn't functioning or the water coming out isn't hot sufficient, you may need to inspect the temperature level setups on your top thermostat. Make certain the circuit breaker is switched off prior to doing anything. Open the accessibility panel as well as press the red button for temperature reset above the thermostat. This should help heat up the water. Transform the circuit breaker back on as well as check if the problem has been resolved.

Inspect the Burner in the Hot Water Heater:


If it's not a power issue, after that try taking a look at your heating element if it is still working. Check each of your burner to ensure the problem isn't with any one of them. If any one of them is malfunctioning, change that part and after that check whether the warm water is back on.

Conclusion


Hot water heater issues are not always major. Many of them are due to small concerns like a blown fuse or damaged heating element. Replacing the defective parts need to suffice. However, if you are still not able to resolve the problem, give a call to your local plumber to come to get it dealt with.


8 possible reasons why you have no Hot Water


Along with streaming Netflix and having light flood a room when we flick a switch, having hot water flow from our taps and showerheads whenever we want is an oft-overlooked modern miracle of homeownership. That's why, when that flow goes cold, it can be shocking — and not just in a "Wow, that's freezing" kind of way while you're in the shower.


Water Leak


Before hot water reaches your taps and showerheads, it needs to spend some time in your water heater. This appliance, which can be either gas- or electric-powered, takes the cold water that enters your home from your well or utility company and cooks it until it gets hot. It's akin to an electric tea kettle.



Obviously, if your water heater is leaking, it will never fill with water so it won't have anything to warm. To see if this is the case, simply examine the area around the water heater to see if it is wet. If so, you'll likely need to replace the unit, but you can also call in a pro for a second opinion and to see if it is fixable. Sometimes leaks can happen around fixtures on the water heater, and if so, the solution might be as simple as replacing them.


Gas Heater: Gas Leak


If your hot water is fueled by natural gas and there is a leak in the supply line or where the line enters the tank, the appliance won't have the power it needs to heat up your water. The result is not only inconvenient, but it can be extremely dangerous as well. If you smell gas when you investigate your water heater, call your gas utility company immediately and report it as an emergency. It might also be prudent to leave your home until a repair person from the company arrives. Your utility company will usually fix any kind of gas leak. However, in terms of getting your water heater working again, you'll need to relight the pilot and wait a while to see if it is functioning properly. You can call in a water heater specialist or plumber to help with this.


Gas Heater: Pilot Light Problems


There are two other issues with gas-powered water heaters that can lead to a loss of hot water. The first is a pilot light that's blown out. The pilot light is the source of a constant flame inside your water heater. When the heater determines the need to heat up the water it is holding, it will open a valve that will cause gas to flow over the pilot light and cause it to ignite. To see if your pilot light is functioning, there is usually a small window in the front of the water heater. If you can't see a flame, remove the access panel and see if that helps you locate it. If there is still no flame, you'll need to relight it in accordance with the manufacturer's instructions.



Your pilot light should burn with a bright blue flame. If not, make sure there are no drafts affecting it, which could keep it from functioning properly. If the flame looks yellow, it might be a sign of the presence of carbon monoxide, which spells trouble and needs to be looked at right away by a technician.


Gas Heater: Faulty Thermocouple


The second reason why a gas-powered water heater might fail is a faulty thermocouple. This is a small probe that should sit in the pilot light flame. Its purpose is to stop the flow of gas if it senses that the pilot light is out. Sometimes, these probes get knocked off track, so make sure it is directly in the flame. They can also get a buildup on them that prevents their function, so try cleaning yours off with some steel wool or fine-grit sandpaper. If your pilot light won't stay lit and you've tried these steps to fix the thermocouple, it is likely faulty and needs to be replaced. Call a technician.


Electric Heater: Breaker Blues


Electric water heaters don't have pilot lights, because there is no gas to burn in order to heat up the water. Instead, they do their magic through the use of (naturally) electricity. But that's not to say things can't go wrong with them. If your electric water heater isn't working properly, there's a good chance that a breaker was tripped that supplies the appliance power. Check your breaker box and flip any breakers that have switched to the off position back on. If it trips again, then there might be a fault in the water heater, and you'll want to call in a pro to have a look.


Electric Heater: Reaching The Limit


If the breaker is fine, check to see if the high-temperature limit has switched off on the water heater itself. To do so, first turn off the breaker to the unit. Then remove the service panel and press the red button you'll find there. This is the limit switch, and resetting it could solve your problem. To check, replace the panel, turn the breaker back on and listen to see if the water heater is functioning again.


Electric Heater: Heating Element


If these steps don't fix the issue, then you might have a failed heating element, which will need to be replaced. Unless you are comfortable with such repairs, calling in a technician might make the most sense.

https://www.homeserve.com/en-us/blog/home-improvement/no-water-heater/



Hopefully you enjoyed reading our section on No Hot Water — Water Heater Repair. Thanks for taking the time to read through our short article. I beg you take the time to share this page if you liked it. Many thanks for going through it.


Expert plumbing solutions, one click.

Leave a Reply

Your email address will not be published. Required fields are marked *